Cleanup pair octaves

NuEVI/src/TODO

@@ -1,9 +1,6 @@
 1. LED abstraction code
 5. Refactor CV behavior into module
-6. 9dof sensor code
+7. LH fingerings
-7. Alternate fingerings
-8. Encoder midi
 
 - Lever mode: pb
 - Breath suck control?
-- 

NuEVI/src/config.h

@@ -10,8 +10,9 @@
 #define ON_Delay   20   // Set Delay after ON threshold before velocity is checked (wait for tounging peak)
 #define CCN_Port 5      // Controller number for portamento level
 #define CCN_PortOnOff 65// Controller number for portamento on/off
-#define START_NOTE 24 // set startNote to C (change this value in steps of 12 to start in other octaves)
+#define START_NOTE 36 // set startNote to C (change this value in steps of 12 to start in other octaves)
 #define FILTER_FREQ 10.0
+#define BREATH_THR_MAX_BOOST 40.0
 #define CAP_SENS_ABSOLUTE_MAX 1000 // For inverting capacitive sensors
 #define PRESSURE_SENS_MULTIPLIER 10 // Multiply pressure sens so it's not a float
 #define CALIBRATE_SAMPLE_COUNT 4
@@ -31,6 +32,7 @@
 #define BTN_PRESET 0x8
 #define KNOB_CURVE_THRESHOLD 100
 #define KNOB_CURVE_MULTIPLIER 5
+#define KNOB_DISPLAY_TIME 500
 
 // Send breath CC data no more than every CC_BREATH_INTERVAL 
 // milliseconds

NuEVI/src/globals.h

@@ -20,9 +20,9 @@
 
 enum PinkyMode : uint8_t {
     PBD = 12,
-    GLD = 25,
+    GLD = 26,
-    MOD = 26,
+    MOD = 27,
-    QTN = 27,
+    QTN = 28,
 };
 
 enum FingeringMode : uint8_t {
@@ -105,6 +105,8 @@ struct instrument_state_t {
   int pitchBend = 8192;
   int pbSend = 8192; // Pitch bend actually sent, modified by vibrato, etc
   byte knobVals[4];
+  byte lastKnobVal;
+  unsigned long lastKnobTime;
   byte rollCCVal = 0;
   byte tiltCCVal = 0;
 
@@ -119,6 +121,7 @@ struct instrument_state_t {
   // Calibration
   int16_t breathZero; // this gets auto calibrated in setup
   int16_t breathThrVal; // this gets auto calibrated in setup
+  int16_t breathMovingThrVal;
   int16_t breathMaxVal; // this gets auto calibrated in setup
   int16_t breathAltZero; // this gets auto calibrated in setup
   int16_t breathAltThrVal; // this gets auto calibrated in setup

NuEVI/src/hardware.cpp

@@ -9,6 +9,8 @@
 FilterOnePole breathFilter;
 FilterOnePole breathAltFilter;
 FilterOnePole spikeFilter;
+FilterOnePole tiltFilter;
+FilterOnePole rollFilter;
 
 Adafruit_MPR121 touchSensorKeys = Adafruit_MPR121();
 Adafruit_MPR121 touchSensorUtil = Adafruit_MPR121();
@@ -44,6 +46,8 @@ void initHardware() {
   breathFilter.setFilter(LOWPASS, FILTER_FREQ, 0.0); // create a one pole (RC) lowpass filter
   breathAltFilter.setFilter(LOWPASS, FILTER_FREQ, 0.0); // create a one pole (RC) lowpass filter
   spikeFilter.setFilter(HIGHPASS, 200, 0.0); // create a one pole (RC) lowpass filter
+  tiltFilter.setFilter(LOWPASS, 2, 0.0); // create a one pole (RC) lowpass filter
+  rollFilter.setFilter(LOWPASS, 2, 0.0); // create a one pole (RC) lowpass filter
   icmSensor.begin_I2C(ICM20948_I2CADDR_DEFAULT, &MainI2CBus);
 
   ledStrip.begin();
@@ -179,7 +183,7 @@ icm_result_t readICM() {
   icmSensor.getEvent(&accel, &gyro, &temp, &mag);
 
   return {
-    mag.magnetic.y,
+    tiltFilter.input(mag.magnetic.y),
-    mag.magnetic.x,
+    rollFilter.input(mag.magnetic.x),
   };
 }

NuEVI/src/icm.cpp

@@ -0,0 +1,25 @@
+#include "hardware.h"
+#include "midi.h"
+
+void checkICM(state_t &state) {
+  icm_result_t icmSignal = readICM();
+  Serial.print(">roll: ");
+  Serial.println(icmSignal.roll);
+  Serial.print(">tilt: ");
+  Serial.println(icmSignal.tilt);
+  if (ExtraControl::CC == state.currentPreset->icmRollMode) {
+    byte roll =  mapConstrain(abs(icmSignal.roll), 0, 40, 127, 0);
+    if (roll != state.instrument->rollCCVal) {
+      midiSendControlChange(state.currentPreset->icmRollCC, roll);
+      state.instrument->rollCCVal = roll;
+    }
+  }
+
+  if (ExtraControl::CC == state.currentPreset->icmTiltMode) {
+    byte tilt =  mapConstrain(abs(icmSignal.tilt), -20, 40, 0, 127);
+    if (tilt != state.instrument->tiltCCVal) {
+      midiSendControlChange(state.currentPreset->icmTiltCC, tilt);
+      state.instrument->tiltCCVal = tilt;
+    }
+  }
+}

NuEVI/src/icm.h

@@ -0,0 +1,8 @@
+#ifndef __ICM_H
+#define __ICM_H
+
+#include "settings.h"
+
+void checkICM(state_t &state);
+
+#endif

NuEVI/src/led.cpp

@@ -25,6 +25,14 @@ void singleLED(int n, int color) {
 // 0 -> 0, 0, 0, 0, 0, 0, 0, 0
 
 void ledFullMeter(byte indicatedValue, int color){
+  static byte lastVal = 0;
+  static int lastColor = 0;
+  if (lastVal == indicatedValue && lastColor == color) {
+    return;
+  }
+  lastVal = indicatedValue;
+  lastColor = color;
+
   int scaledVal = indicatedValue;
   ledStrip.setBrightness(1);
   for (int i = 0; i < 8; i++) {
@@ -79,5 +87,9 @@ void statusLedBlink() {
 }
 
 void updateSensorLEDs(instrument_state_t &state) {
+  if (millis() - state.lastKnobTime < KNOB_DISPLAY_TIME) {
+    ledFullMeter(state.lastKnobVal, 0x00FF00);
+  } else {
     ledFullMeter(state.breathCCVal, 0x0000FF);
   }
+}

NuEVI/src/menu.cpp

@@ -516,7 +516,7 @@ public:
     }
 
     if (_focused && input.changed && input.knobMenu != 0) {
-      _cursorPos = (_cursorPos + input.knobMenu) % _entries.size();
+      _cursorPos = ((_cursorPos + input.knobMenu) + _entries.size()) % _entries.size();
       draw(false);
       redrawValue = true;
     }

NuEVI/src/xEVI.cpp

@@ -13,6 +13,7 @@
 #include "led.h"
 #include "test.h"
 #include "FilterOnePole.h"
+#include "icm.h"
 
 /*
 NAME:                 xEVI
@@ -92,6 +93,7 @@ bool configManagementMode = false;
 bool testMode = false;
 
 FilterOnePole breathCCFilter;
+FilterOnePole breathBaselineFilter;
 
 //_______________________________________________________________________________________________ SETUP
 
@@ -444,35 +446,15 @@ void sendCC() {
           midiSendControlChange(state.currentPreset->knob4CC, val);
           break;
         }
-      }
 
         state.instrument->knobVals[i] = val;
+        state.instrument->lastKnobVal = val;
+        state.instrument->lastKnobTime = millis();
       }
     }
-
-  icm_result_t icmSignal = readICM();
-  Serial.print(">roll: ");
-  Serial.println(icmSignal.roll);
-  Serial.print(">tilt: ");
-  Serial.println(icmSignal.tilt);
-  if (ExtraControl::CC == state.currentPreset->icmRollMode) {
-    byte roll =  mapConstrain(abs(icmSignal.roll), 0, 40, 127, 0);
-    if (roll != state.instrument->rollCCVal) {
-      midiSendControlChange(state.currentPreset->icmRollCC, roll);
-      state.instrument->rollCCVal = roll;
   }
 }
 
-  if (ExtraControl::CC == state.currentPreset->icmTiltMode) {
-    byte tilt =  mapConstrain(abs(icmSignal.tilt), -20, 40, 0, 127);
-    if (tilt != state.instrument->tiltCCVal) {
-      midiSendControlChange(state.currentPreset->icmTiltCC, tilt);
-      state.instrument->tiltCCVal = tilt;
-    }
-  }
-
-}
-
 // Re-zero floating calibration values
 void rezero() {
   instrument.vibThr = instrument.vibZero + state.currentPreset->vibSquelch;
@@ -602,7 +584,7 @@ int readOctave() {
       if (rollers[0]) {
         octaveR = 1;
       } else if (rollers[5]) {
-        octaveR = 6;
+        octaveR = 7;
       }
     }
   } else if (rollerMode == RollerMode::PARTIAL || rollerMode == RollerMode::PARTIAL_EXTEND) {
@@ -632,6 +614,8 @@ int readOctave() {
   if (extend && octaveR == 0) {
     if (rollerMode == RollerMode::HIGHEST_EXTEND && lastOctaveR == 6) {
       octaveR = 7;
+    } else if (rollerMode == RollerMode::HIGHEST_PAIR_EXTEND && lastOctaveR == 7) {
+      octaveR = 8;
     } else if (rollerMode == RollerMode::PARTIAL_EXTEND && lastOctaveR == 7) {
       octaveR = 8;
     } else if (lastOctaveR == 1) {
@@ -785,7 +769,8 @@ void initState() {
 
   instrument.activeMIDIchannel = state.currentPreset->MIDIchannel;
   midiInitialize(state.currentPreset->MIDIchannel);
-  breathCCFilter.setFilter(LOWPASS, 3, 0.0); // create a one pole (RC) lowpass filter
+  breathCCFilter.setFilter(LOWPASS, 3, 0.0);
+  breathBaselineFilter.setFilter(LOWPASS, 1, 0.0);
 }
 
 /**
@@ -802,7 +787,7 @@ void readUtil() {
 /**
  * Send CC data when needed
  */
-void sendCCs() {
+void handleCCs() {
   static unsigned long ccBreathSendTime = 0L; // The last time we sent breath CC values
   static unsigned long ccSendTime = 0L;      // The last time we sent CC values
   static unsigned long ccSendTime2 = 0L;     // The last time we sent CC values 2 (slower)
@@ -819,6 +804,7 @@ void sendCCs() {
     readUtil();
     pitch_bend();
     sendCC();
+    checkICM(state);
     ccSendTime = currentTime;
   }
   if (currentTime - ccSendTime2 > CC_INTERVAL_PORT) {
@@ -833,6 +819,43 @@ void sendCCs() {
   }
 }
 
+/**
+ * Read the breath sensors according to the active mode
+*/
+void readBreath() {
+
+  int16_t breathSignal = constrain(readPressure(), BREATH_LO_LIMIT, BREATH_HI_LIMIT); // Get the filtered pressure sensor reading from analog pin A0, input from sensor MP3V5004GP
+  int16_t spikeSignal = constrain(readSpikePressure(), -SPIKE_HI_LIMIT, SPIKE_HI_LIMIT);
+  instrument.breathMovingThrVal = constrain(
+    breathBaselineFilter.input((breathSignal + instrument.breathZero) / 2), 
+    instrument.breathThrVal, 
+    instrument.breathMaxVal
+    );
+
+  if (state.currentPreset->breathMode == BREATH_ACC || state.currentPreset->breathMode == BREATH_ACC_AT) {
+    int delta = breathSignal - instrument.breathZero;
+    if (abs(delta) > state.calibration->breathAltThrValOffset) {
+      instrument.breathSignal = constrain(instrument.breathSignal + delta / 10, instrument.breathZero, instrument.breathMaxVal);
+    }
+  } else {
+    instrument.breathSignal = breathSignal + (spikeSignal > 0 ? spikeSignal * state.currentPreset->spikeOnFactor : spikeSignal * state.currentPreset->spikeOffFactor);
+  }
+  instrument.breathAltSignal = constrain(readAltPressure(), BREATH_LO_LIMIT, BREATH_HI_LIMIT); // Get the filtered pressure sensor reading from analog pin A0, input from sensor MP3V5004GP
+
+    Serial.print(">breathThr:");
+    Serial.println(instrument.breathThrVal);
+    Serial.print(">breathMovingThr:");
+    Serial.println(instrument.breathMovingThrVal);
+    Serial.print(">note:");
+    Serial.println(state.mainState);
+    Serial.print(">spike:");
+    Serial.println(spikeSignal);
+    Serial.print(">breath:");
+    Serial.println(breathSignal);
+    Serial.print(">combo:");
+    Serial.println(instrument.breathSignal);
+}
+
 /**
  * Main instrument state machine
  */
@@ -842,7 +865,7 @@ void runStateMachine() {
   int fingeredNote = noteValueCheck(readSwitches() + readOctave());
   if (state.mainState == NOTE_OFF) {
     handleOffStateActions();
-    if (instrument.breathSignal > instrument.breathThrVal && state.mainState == NOTE_OFF) {
+    if (instrument.breathSignal > instrument.breathMovingThrVal && state.mainState == NOTE_OFF) {
       // Value has risen above threshold. Move to the RISE_WAIT
       // state. Record time and initial breath value.
       breath_on_time = millis();
@@ -850,7 +873,7 @@ void runStateMachine() {
       state.mainState = RISE_WAIT; // Go to next state
     }
   } else if (state.mainState == RISE_WAIT) {
-    if ((instrument.breathSignal > instrument.breathThrVal)) {
+    if ((instrument.breathSignal > instrument.breathMovingThrVal)) {
       // Has enough time passed for us to collect our second sample?
       if ((millis() - breath_on_time > state.currentPreset->velSmpDl) || (0 == state.currentPreset->velSmpDl) || state.currentPreset->fixedVelocity) {
         noteOn(fingeredNote, instrument.breathSignal, initial_breath_value);
@@ -862,7 +885,7 @@ void runStateMachine() {
       state.mainState = NOTE_OFF;
     }
   } else if (state.mainState == NOTE_ON) {
-    if (instrument.breathSignal < instrument.breathThrVal) {
+    if (instrument.breathSignal < instrument.breathMovingThrVal) {
       // Value has fallen below threshold - turn the note off
       midiSendNoteOff(instrument.activeNote); //  send Note Off message
       instrument.breathSignal = 0;
@@ -954,35 +977,10 @@ void loop() {
     return;
   }
 
-  int16_t breathSignal = constrain(readPressure(), BREATH_LO_LIMIT, BREATH_HI_LIMIT); // Get the filtered pressure sensor reading from analog pin A0, input from sensor MP3V5004GP
+  readBreath();
-  int16_t spikeSignal = constrain(readSpikePressure(), -SPIKE_HI_LIMIT, SPIKE_HI_LIMIT);
-
-
-  if (state.currentPreset->breathMode == BREATH_ACC || state.currentPreset->breathMode == BREATH_ACC_AT) {
-    int delta = breathSignal - instrument.breathZero;
-    if (abs(delta) > state.calibration->breathAltThrValOffset) {
-      instrument.breathSignal = constrain(instrument.breathSignal + delta / 10, instrument.breathZero, instrument.breathMaxVal);
-    }
-  } else {
-    instrument.breathSignal = breathSignal + (spikeSignal > 0 ? spikeSignal * state.currentPreset->spikeOnFactor : spikeSignal * state.currentPreset->spikeOffFactor);
-  }
-  instrument.breathAltSignal = constrain(readAltPressure(), BREATH_LO_LIMIT, BREATH_HI_LIMIT); // Get the filtered pressure sensor reading from analog pin A0, input from sensor MP3V5004GP
-
-  /*
-    Serial.print(">breathThr:");
-    Serial.println(instrument.breathThrVal);
-    Serial.print(">note:");
-    Serial.println(state.mainState);
-    Serial.print(">spike:");
-    Serial.println(spikeSignal);
-    Serial.print(">breath:");
-    Serial.println(breathSignal);
-    Serial.print(">combo:");
-    Serial.println(instrument.breathSignal);
-  */
 
   runStateMachine();
-  sendCCs();
+  handleCCs();
 
   // cvUpdate();
   midiDiscardInput();